Chad

Help with dynamic IP and active mode

16 posts in this topic

I can't get this going at all. Impossible

I have setup everything as should and I get no search results at all

See attached. What to do?

I have a Belkin Pre-N router and Optimum Online ISP

DC++ works fine, why not APEX?

post-3547-1166555190_thumbgif

post-3547-1166555193_thumb.jpg

post-3547-1166555197_thumb.jpg

Share this post


Link to post
Share on other sites

Click on the Get IP Address button and it''l grab your dynamic IP.

Share this post


Link to post
Share on other sites

Click on the Get IP Address button and it''l grab your dynamic IP.

I know that. That IP shown is my IP address, still does not work

Share this post


Link to post
Share on other sites

AFAICS your LAN IP is 192.168.2.1, and you are setting to 192.168.2.2.

Share this post


Link to post
Share on other sites

I know that. That IP shown is my IP address, still does not work

So then you haven't set up your ports correctly. Use this guide for that.

Share this post


Link to post
Share on other sites

Do you mind splitting the topic and moving to Support? Wish I could do it...

Share this post


Link to post
Share on other sites

AFAICS your LAN IP is 192.168.2.1, and you are setting to 192.168.2.2.

maybe, but i suspect this is the ip address of the router, 192.168.2.1.

AFAICS, do you have more then one network card or do you have a software firewall. could you also confirm 192.168.2.2 is you addy, e.g. windows -> run "cmd /k ipconfig". TBH you are probably best trying to get hold of some one in TGO. Could you also say what hubs you are tying to search in. some hubs require you to reg before you can search.

Share this post


Link to post
Share on other sites

And do not rely on "Check Connection" for now. :)

Share this post


Link to post
Share on other sites

I did not setup port forwarding incorrectly unless your blind :)

It works fine for DC++, just not in APEX DC++

In APEX, I can't use manual port forwarding, can't use passive, can't use

anything! Why does it work in DC++ then?

I'm using official Vista RTM

Limewire, DC++ both work but not APEX

I can grab the public list and connect, but I cannot get file lists nor search results

I do not have software firewall installed, I have Avast Antivirus installed only.

I tried 192.168.2.1 for "network interface for all connections"

What should go in TLS?

Share this post


Link to post
Share on other sites

I'm using official Vista RTM

...

What should go in TLS?

How can you use official Vista, as it is not out for retail customers as of yet...

TLS, you can leave empty.

Share this post


Link to post
Share on other sites

How can you use official Vista, as it is not out for retail customers as of yet...

And we do not support people downloading pirated software.

Share this post


Link to post
Share on other sites

And we do not support people downloading pirated software.

You people are so clueless.

RTM = Release to Manufacturers

I am subscribed to MSDN and it is OFFICIAL RELEASE!

Get with the program blind mice!

Share this post


Link to post
Share on other sites

PLZ, don´t be rude.

Use bind address to map your LAN IP and use the same IP in router. If you have ApexDC 0.4.0 then it have a drop down box with your LAN IP in bind address.

There are more things you have to check like software firewall, try disable it and try again.

Share this post


Link to post
Share on other sites

You people are so clueless.

RTM = Release to Manufacturers

I am subscribed to MSDN and it is OFFICIAL RELEASE!

Get with the program blind mice!

I've got RTM too, though i ain't a MSDN subscriber (borrowed it from a friend :whistling:), unactivated Vista isn't an illegal software, we know that, but don't be rude.

Share this post


Link to post
Share on other sites

You people are so clueless.

RTM = Release to Manufacturers

I am subscribed to MSDN and it is OFFICIAL RELEASE!

Get with the program blind mice!

I know what RTM means, thank you but since you didn't tell that you are an msdn subscriber it's perfectly normal for us to assume that your version would've been pirated as with majority of people that use vista now that's the case (in this forum anyways since ApexDC is a P2P software after all, even if we do not approve nor encourage usage for illegal activities...)

Share this post


Link to post
Share on other sites